lucas POD part numbers
is there a stock lucas part number (i assume these injectors are for some stock application and not custom made?) where i can go to my local injection shop who has an old lucas sign and order a set...
View ArticleCarrier Bearing suggestions, maybe a one piece drive shaft instead?
I am about to do a transmission swap so I figure now is the time to replace my bad carrier bearing and any U-joints as well. What is the best carrier bearing for our trucks? I have also read a little...
View Article47re & pto/tcase box
Have friend that hauls junk cars and drug in a 96 v10 truck. It is 2wd but has the dummy tcase for the pto. Does not have a pto on it. He wants $300 for trans and case. I would be willing to pull it...
View ArticleFullcuts w/ seats - $150 shipped
I have a set of fullcuts with seats. Will ship anywhere in the u.s. Call me if you want em. Dont post or pm me. 8126980851
View ArticleRecommendations for good shop?
Folks, I need some input from members that live in the Los Angeles county area in California. I'm going to be working in Santa Clarita for 8-11 months and would like some recommendations for a...
View Articleraptor FRRP install help
I bought a frrp and went to install it today and found that i have an in tank lift pump, im not sure if im supposed to remove this in tank pump or just leave it and install the frrp.. any help is...
View Article4th gen bumper
Does anyone know if a 4th gen bumper can or will fit on a 3rd gen truck? and are the tailgates interchangable?
View ArticleCustom Smarty Tune for MPG
I am currently running my Smarty on SW7, Tq 3, Rail 2, Timing 2,Waste gate off (kind of my fun tune). I have tried SW3, SW5 and SW9 and played with all the settings up and down with each and truck runs...
View ArticleClik here to view.
NJ: 07 MegaCab with extras
Looking to sell my 07.5 Megacab w/ 45000 mi. White 4x4, Was used to tow a 9k boat about 4 times a year since new. Comes with the following extras: Full tilt Comp68 transmission. AMP Steps ARP 425 studs...
View ArticleNerf Bar Fitment Issues
Bought some of those cheap ($200), black, wheel to wheel nerf bars from eBay, put them on the truck, and for the love of god, I cannot get them to follow the cab lines! Has anyone else had fitment...
View Articlecummins hp
hi everybody i am new here and have a simple question regarding mods i did to my truck,i want to know approximatly how much power it is puting out as i have no acce ss to a dyno.the mods are as follows...
View ArticleEBC yellow stuff pads and G2 caliper paint
Just installed new pads and the ebc's will put you thru the windshield!!!Great product and will definitely be purchasing them again.The caliper paint is amazing as well able to withstand temps up to...
View ArticleOEM 17'' Wheel Specs (2012 vs 2004)
I am wanting to purchase a set of OEM Aluminum stockers for my 2004 Ram 2500. I found a great deal yesterday, but the set is from an 2012 Ram and the owner tells me they have a different offset then my...
View Article97 12 valve fuel issue
truck would just crank and not turn over, i took your advice and manually engaged the shut off solenoid and it started right up. Thank you! Now I am not sure what to replace , the solenoid, the relay...
View ArticleWhite Smoke
Last night I noticed for the first time a puff of white smoke, truck was running fine, and it went away quick, the truck didn't overheat(my first thought was head gasket), so pulled over when the truck...
View Articlecomplete 96 12v engine in PA
Have a complete 12v engine from a 96 2500 ran good when pulled has 207xxx miles on it has everything from turbo to oil pan all accessories might have a starter adapter plate and flex plate for a 47re...
View ArticleCat and DPF + full exhaust for sale from turbo back
Don't really know the going rate,just sitting around and dont have a use for it.Best offer!!!
View ArticleWhat turbo would you run?
The truck is a 97 1500 2wd. It will see some DD but mostly the drag strip. Suspension is a 3/6 drop with ladder bar and coilover and a track bar. Dana 70 with a ratchet style locker. Tire size is up in...
View ArticleDid Fuel wheel fit on my 07
Hi Guys I want to put Fuel Octane model wheel on my truck, but on their web site they says it`s a 125.2mm Bore !!!! http://mhtwheels.com/pdf/specs/D508-D509%20Octane2.pdf I read on this forum that our...
View Article