Turbo issues???
So just 2 days ago the head gasket went out on my '11 and the dealership changed that out for me. Drove it home.... 150 miles, no problem, hooked up to my 6 place enclosed and 6 sleds and drove about...
View Articlelucas motor oil
Anyone running the lucas oil or additives and not amsoil? If so or if not, why?
View ArticleWTB Dog dish hub cap/caps
I need a hubcap for my truck and I can't find one anywhere.. I only need one. It's the back one so it dosent have the hole.. I would buy a whole set if i had to. It's for a 4x4 so 2 need to have the...
View ArticleClik here to view.
Custom-made full stereo Bezel
Custom-made full stereo Bezel for double din with three gauge mount glassed in under a/c controls. Comes with full panel with Cigarette Lighter and AC controls. $150 ( out 0f an 2004) ( FYI still...
View ArticleNew to diesels & question...
I have a 99 2500 24v w/ automatic. When towing, should you take it out of overdrive? Sure seems to be screamin close to 3k on the tach at 60 mph. Does it do any good to take out of OD or not?...
View ArticleDealers that do delete in B.C. Canada
Hi just bought a brand new 2012 dodge 3500 and wanted to do the delete setup but am worried about warranty issues. Does any one know of a dealership that will install and honour any warranty issues?...
View ArticleClik here to view.
WI: 1950 Chevrolet Styline
Just throwing it out there, Need a new DD. mild built sbc,turbo 350 trans,10 bolt posi rear,320 gear,power brakes,tilt wheel,fm cd player,vintage air/heat,electric door openers,custom pro done...
View Article6inch rough country lift FOR SALE
like the title says i have a 6 inch rough country lift it has been on my 04 i am lowering it back down and would like to sell it is about 1 year old the front springs are powdercoated gray and all the...
View ArticleLooking for tire thread
I saw earlier tonight but can't find it again. It's about fitting 37s. It's about 80 pages long. Anyone know the one I'm talking about and have a link Sent from some new fangled gadget
View Articlerebuild
Im puttin a cam springs tappets and a few other things into my engine now, and i decided to pull it to paint it and make it look pretty. Since its out and mostly everything is apart im going to need...
View Articlepiston cooling jets or plugs
Early 2004 model c code 5.9 undergoing a full rebuild. Ran into something not covered in my book. I have the J style cooling jets installed in the block, and in 5 of the main bearing saddles there are...
View ArticleWTT 07.5 duramax with 12" lift for a 2010 or newer cummins
I have a 07.5 ccsb duramax 12" cognito lift 20x10 jesse james lawless 8's with 38" mtz's efi live with a dsp 5 and 4" turbo back exhaust and a 6" rbp tip 2 tone blk and grey leather and a bed rug...
View ArticleTransfer case problem in 4x4 mode H.E.L.P
Hello folks, Once again another problem and back to forum! I have bad noise comming from transfer case and it's very loud and I feel some thing is slipping inside, Chain?gears? only does in in 4x4,...
View ArticleCustom "C" Cummins Vinyl/Decal
Have been looking around and can find the basic C logo for the back window but I'd like to do a custom one. I could stop by a vinyl printing shop but I figured I'd ask. I am looking for a custom C...
View ArticleClik here to view.
TX: 2008 QCLB 2500 4x4 6.7
2008 Dodge 2500 4x4 6.7 Cummins with auto trans. Upgrades: H&S trans tune, EFI live tuned, S&B intake, deleted, Dynatrac free spin hubs, Dynalock lockers, Dynatrac rebuildable upper and lower...
View ArticleStock flex plate
Comes with bolts. $50 shipped. Sent from my DROID RAZR using AutoGuide.Com Free App
View ArticleDetroit Truetrac D60-30 spline 3.54 ratio
Detroit TrueTrac locker for a D60, 3.54 ratio. $500 in a carrier ready for your ring gear, $400 for just the locker.
View Articlesmarty in Edmonton
Does anyone have a smarty in Edmonton that I could use to turn on my three cylinder high idle? Any help with this would be greatly appreciated. Thanks, Tylor
View ArticleFound a clip in my tranny pan
So i put my new mag-hytech trans pan on and i found a piece of metal stuck to the magnet in the stock pan. It was about 2" long and arched, as if it was part of a circular clip. Anyways where do i...
View ArticleAnyone else have airdog problem?
I got an airdogll 165. Having problems. A few weeks ago I was hooking to a trailer the truck was idling and then just died. Hit the key it fired right up then died again. 10 min later it fired up and...
View Article