A518 to Getrag
Hello, I'm in the process of a manual swap and I came across the transfer case linkage....it doesn't line up....what have you guys done in this situation???
View ArticleWhich rods
My 1996 215hp truck is getting a rebuild. It has England rods coming out (210k miles) but I also have a set of Brazil rods (unknownmiles) that have been shot peened/polish from CPP. Have had them in...
View ArticleCrossmember bolts
I noticed today I am missing most of the bolts where my 5600 crossmember bolts to the frame, I have 2 left on each side however when I tried to tighten them up they wont tighten. I think the PO threw...
View ArticleU010C code... Not the turbo
I'm new on here because I'm having an issue and I'm running out of ideas. I have a 2009 2500. Truck is deleted and has a fleece Cheetah vgt. A few weeks ago the check engine light came on. The code was...
View ArticleTo much boost??
Added a 66 mm turbo 3rd gen swap. At wot turbo sounds like air is blowing out. Sounds similar to when you have a back window down an the air starts moving. I’m thinking I need a bigger intake manifold...
View ArticleCenter console
In the market for a 2019 2500 Cummins. Can you get the tradesman or big horn with a center console? I have searched everywhere and need help ASAP. Don’t want to spend 50k plus on Laramie. Looking for...
View ArticleIOD fuse problems
2001 2500 Cummins. I've got no power to my stereo or interior lights. My IOD fuse keeps getting burnt ends, but not blowing. I have power at at the IOD fuse terminal. It's been an intermittent problem...
View ArticleHeadlight switch wiring questions
I lost my headlights driving home and figured it was just the headlight switch. I replaced the switch and still my headlights, parking lights, dash lights, and cab lights are out. I found the following...
View ArticleDoors
So I have a 01 Cummins and when I close the doors it still looks like the doors are open when they are shut! How do I make them flush with the body what can I do??
View ArticleMisfire after washing engine bay
I recently bought an 01 cummins with 350k. It had a lot of oil sludge and build up on the engine and in the bay. I wanted to wash it so I covered all the electrical plugs and the ecm with tinfoil. I...
View ArticleTiming with new mods
Should I take my 1992 somewhere to get the timing adjusted or is it easily doable from home? Im updating my sig now, but here are the mods that are on the way ill be putting on s362sxe ducky 5x.014 sac...
View ArticleEGR Valve motor
Hello guys. I was wondering if anyone knows where to get the EGR Valve motor. I got a code P2593 saying that it was an EGR Cooler Bypass so I took off the EGRvalve and the cooler and I cleaned both...
View ArticleCPS Tune and Pedal Commander
I have a pedal commander and Calibrated Power Solutions Emissions intact tuning. Should I remove the Pedal Commander or can I use both ? Thanks in advance for the info
View ArticleHeadgasket Failed
Well the headgasket finally gave up on me last weekend while dragging the camper with a marginal to bad thermostat and bad tuning. I was able to get to my destination and then home again but she was...
View ArticleWindow switch
I recently added a relay kit to my doors to keep my mirror lights on as both running lights and as turn signals, and I noticed that my passenger side front window switch keeps cranking the window down...
View ArticleDEF Consumption
So I bought my truck mid February (14 2500 Laramie 6.7) and have put about 1500 miles on it, several tanks of fuel and even hauled/towed pretty heavy over the mountains a couple times and my DEF gauge...
View ArticleClik here to view.
05 f250 common rail conversion
Since we're not working much in the shop due to COVID, I decided to dive into this project. I'll be adding to it as I go but here's where we started. Everything has been pieced together from spare...
View Article2019 Leather steering wheel upgrade
All, I was going to see if someone could help me out on upgrading my steering wheel. I have a 2019 tradesman with the 8.4 u connect. I’m wanting to upgrade to a leather wheel with audio controls on...
View ArticleUsing two front crank seals
This will be my third time replacing the front crank seal on my ‘97 12 valve. The first time I replaced it 3/4 years ago I had zero leaks. I pulled the timing cover to install a PDD adjustable timing...
View ArticleRe-Tuning to stock
I am gonna be putting eveything back on my truck and re- tuning it back to stock with an ez lynk. For anyone who has done this how many miles did it take for everything to reset and start working like...
View Article
![[imports/adg/photos/213899875_Police-Car-Lights-2.jpg]](http://wehco.media.clients.ellingtoncms.com/imports/adg/photos/213899875_Police-Car-Lights-2_t600.jpg?4326734cdb8e39baa3579048ef63ad7b451e7676)
